search

Cobalt-digital COMPASS 9253 2x4 AES Audio Distribution Amplifier, Manuel d'utilisateur Page 13

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 20
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 12
13
EQ Switch — SW1 and SW2
The EQ Switches (SW1 and SW2) are used to insert the cable equalizer into the incoming AES/EBU
signal. The 9253 can recover digital audio signals conforming to AES/EBU specifications and
transmitted over 75ohm, coaxial cable, up to 600 metres (2000 ft) long without equalization. For cable
lengths in excess of 600 metres, we recommend that the input equalization be activated. Note that
switching the EQ in and out can cause audible artefacts.
• Pressing the EQ Switches SW1 or SW2 will activate the appropriate yellow EQ
LED to indicate this feature is activated.
• While the EQ Switches SW1 or SW2 are activated pressing it again will disable
the EQ and the yellow EQ LED will go off.
LEDs
The front-edge of the card features LEDs that display the status of the input signals.
As selections are made in the menus, (refer the subsequent chapter for complete menu
descriptions), the LEDs display the status of the input signals. Descriptions are provided in the
following table:
LED Color Location Display and Description
Lock 1
Green
Top of the
card
When illuminated there is a valid AES/EBU signal at the input of
AES1.
No Lock
1
Red
Second
from the
top
When illuminated a valid AES/EBU signal is not present at the input
of AES 1
EQ 1 Yellow
Third from
the top
When illuminated this indicates that the cable EQ for AES 1 has
been inserted by pressing SW1 or that feature has been enabled
through Dashboard.
Lock 2
Green
Fourth from
the top
When illuminated there is a valid AES/EBU signal at the input of AES
2.
No Lock
2
Red
Fifth from
the top
When illuminated a valid AES/EBU signal is not present at the input
of AES 2.
EQ 2 Yellow
Sixth from
the top
When illuminated this indicates that the cable EQ for AES 2 has
been inserted by pressing SW2 or that feature has been enabled
through Dashboard.
Com
Activity
Green
Seventh
from the
top
When illuminated this indicates that the 9253 is communicating to
Dashboard through the CAN bus.
Error
Red
Eighth from
the top
When illuminated this indicates that there is an error in the
communications to Dashboard through the CAN bus.
Table 1. Status LED Descriptions
Vue de la page 12
1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Accessoires pour la vidéo Cobalt-digital COMPASS 9253 2x4 AES Audio Distribution Amplifier,
Accessoires pour la vidéo Cobalt-digital COMPASS 9067 Upconverter Manuel d'utilisateur   (90 pages)
Accessoires pour la vidéo Cobalt-digital FUSION 3G 9901-UDX 3G_HD_SD Up Down_Cross Converte Manuel d'utilisateur   (128 pages)
  • Allflex Automation-components CameraMan ECOserver Aeroqual
  • Emerson PC/postes de travail Roland Instruments de musique Foundry Networks Points d'accès WLAN Sony Lecteurs de livres électroniques Cingular Téléphones mobiles
  • Crest Audio X-VCA Mitsubishi Electric MSZ-SF50VE Electrolux EL4103A Acer M310 Rotel RC-1550
  • Casio KL-C500 Manuel de l'utilisateur Eaton 5115 Guide de l'utilisateur Sony CMT-NE3 Manuel de l'utilisateur Indesit LI8 S1 X Guide de l'utilisateur Rubicon-express RE8000 Manuel de l'utilisateur