Cobalt-digital COMPASS 9223 Dual-Channel 3G_HD_SD MPEG-4 Encoder Manuel d'utilisateur Page 20
- Page / 100
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
20 9223-OM (V2.0)
Configuration Tabs
In general, the encoder user interface will change as a function of the parameter selections made,
to remove illegal parameter combinations.
Selections made in any of the encoder configuration screens do not take effect until the Apply
button is pressed. If you wish to discard the changes made to the user interface, press the Cancel
button. The Apply/Cancel buttons are present in all the tabs and will be grayed out until
changes are made. At any given point in time, the currently running encoder configuration can
be inspected in the Encoder Statistics Tab, described later in this document.
Video Input Auto-Detection
The 9223 can be set to auto-detect the video input signal, and self-configure for the incoming
resolution and frame rate. This feature allows the encoder to operate in situations where the
video signal can change over time (for example, at the output of a video switch). The 9223 is
even capable of automatically recognizing whether a signal is SDI or composite, and the video
standard for composite signals.
The following points should be considered when using video input auto-detection:
• The available output scaling options are limited, since some options are specific to some
input resolutions.
• If the encoder is not licensed for a given configuration, it will stop encoding if the input
video signal switches to a value that requires this configuration. For example, an SD
encoder configured to output the same resolution as the input will stop if the input signal
switches to HD.
• If the encoder is configured with auto-detection and SDI embedded audio, it will fall
back to analog audio if it detects a composite video signal. If your input can switch
between SDI and composite, either use analog audio for all signals, or make sure that the
corresponding analog audio signal is present at the encoder unbalanced audio inputs
when the video is a composite signal.
Multiple Audio Support
The 9223 can be licensed to offer up to two additional MPEG-1 Layer II audio channels,
regardless of the number of installed encoders. These additional audio channels can be
associated with the first or second encoder. Moreover, a dual-channel encoder can be configured
as a single-channel encoder with combined audio. The following combinations are supported:
• Single Channel Encoders: support for 1, 2 or 3 audio stereo pairs, as follows:
o First stereo pair:
MPEG-1 Layer II, AAC-LC or Dolby Passthrough support
Valid inputs: analog unbalanced audio, SDI embedded (SDI signals only)
o Second stereo pair:
MPEG-1 Layer II support only
- Product Manual 1
- Version 2.0 1
- 2 9223-OM (V2.0) 2
- Copyright 2
- Trademarks 2
- Symbol Meanings 3
- Important Safety Instructions 3
- 4 9223-OM (V2.0) 4
- Environmental Information 4
- Contents 5
- Introduction 7
- Indicators and Switches 9
- Front Indicators 10
- Top Corner 11
- Default IP 12
- 9223 Operation and Management 13
- 14 9223-OM (V2.0) 14
- Product Tab 15
- Configuration Tabs 16
- Network Configuration DNS Tab 17
- Network Statistics Tab 18
- Encoder 1, Encoder 2 Tabs 19
- Video Input Auto-Detection 20
- Multiple Audio Support 20
- Closed Captioning 35
- Active Format Description 36
- Composite 37
- Analog Audio Parameters 38
- A/V Sync Adjustment 38
- PMT Information 38
- AAC-LC Configuration 39
- MPEG-1 Layer II Configuration 39
- Advanced Tab – Mux Parameters 41
- Encoder Connections Tab 43
- ASI/IP Streaming 44
- HTTP Live Streaming 44
- HLS Implementation Notes 48
- Direct HTTP Streaming 49
- The Apply/Cancel Buttons 52
- Encoder Statistics Tab 53
- Indicators 58
- ASI Outputs Tab 61
- ASI Output 62
- Parameters 62
- Input Selection 62
- Connection 62
- ASI Ports: Statistics Tab 63
- IP Outputs Tab 65
- IP Output 66
- Advanced 68
- Active IP Outputs Table 71
- IP Outputs: Statistics Tab 72
- Source Selection 74
- Destination Selection 75
- Connection Statistics Tab 78
- MPTS Configuration Tab 79
- MPTS Configuration Parameters 80
- MPTS PID/Program Allocation 80
- MPTS Statistics Tab 81
- Admin Tab 82
- Admin Firmware Tab 83
- Admin Config Files Tab 85
- User-Saved Configurations 86
- Pre-defined Templates 87
- Admin License Keys Tab 90
- Admin Event Log Tab 91
- Select This 92
- Configure 92
- Playing Video on a Web Page 95
- Web Pages Served by the 9223 96
- Multicast Streaming 97
- Web Browser Support 99
- 9223-OM (V2.0) 100
Produits connexes et manuels pour Accessoires pour la vidéo Cobalt-digital COMPASS 9223 Dual-Channel 3G_HD_SD MPEG-4 Encoder
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels